Audi A6 remote control matching with original car

 1. Imported Audi A6 sedan remote control settings

There are two keys for Audi A6 sedan, use the maintenance key to turn the ignition switch to the "ON" position, close all the doors, use one of the keys to lock the driver's door mechanical lock, make sure all the doors are locked and press The remote control button to close the door, and then press the remote control door open button after about 3 seconds.

The second key is just press the button of the remote control for closing the door twice after you "Make sure all doors are locked", the others are the same.

Audi A6 remote control setting method is as follows.

①Turn on the ignition switch with the auxiliary key and close all doors.

②Turn and hold the key in the locking direction outside the door.

③Press the unlock button on the remote control once, and the side door light should flash once.

④Press the unlock button again after 5 seconds, the door lock should be opened in vain at this time, and the setting of the first key is completed.

⑤ Set the second key, turn on the ignition switch with the auxiliary key, and close all doors.

⑥ Use the second key outside the door to turn it in the direction of locking and keep it.

⑦Continuously press the unlock button of the second remote control twice, the side door light should flash twice at this time.

⑧Press the unlock button again after 5s, the door lock should be automatically opened at this time, and the second key is set.

The steps for setting the third and fourth keys are the same as above, except that when setting the third key, press the unlock button three times continuously in step ③, and when setting the fourth key, press the unlock button four times continuously in step ③.

*Matching method of central door lock remote control transmitter for Audi A6 sedan

①Insert one of the ignition keys into the ignition core and turn it to the "ON" position.

②Close all doors, insert another ignition key into the driver's door lock, and lock the doors with the key.

③ Pull out the ignition switch on the door lock to start the key, press the unlock button, open the door and take out the key in the ignition core, the matching of the central door lock remote control transmitter of the key is completed.

④ Reinsert another ignition key into the "ON" position of the ignition core.

⑤ Repeat steps ② and ③ to complete the transmission matching of the central door lock remote control of another ignition switch start key.

2: Audi A6L car remote control key activation method

The remote control key of Audi A6L sedan often can start the engine, but cannot be remotely controlled. The main reason is that the remote control key is out of power. After the battery is replaced, or the remote control key is not used for a long time, the remote control receiving device is in a "sleep" state. At this time Just activate the function of the remote control key

(1) Insert the remote control key into the ignition switch;

(2) Put the ignition switch in position 2 for at least 30 s;

(3) Pull out the remote control key;

(4) Insert the remote control key and start the engine;

(5) Let the engine run for at least 1 min;

(6) Turn off the engine and pull out the remote control key;

(7) Close all doors;

(8) Press the unlock or lock button on the remote control key, and the central control door lock in the car should be able to unlock or lock, indicating that the remote control function of the remote control key is successfully activated.

Note, if the above operation still does not work, you can do the following:

Close all doors; wait at least 5 minutes, then the instrument lights will turn off and the vehicle will enter "sleep" mode; enter the vehicle, start the engine; turn off the engine after a few minutes, and disconnect the ignition switch; press the unlock on the remote control or Lock button, the central control door lock in the car should be able to unlock or lock, indicating that the remote control function of the remote control key is successfully activated.

3: Audi A6 wireless remote control key synchronization processing method

If the car cannot be unlocked or locked by remote control, the wireless remote control key must be synchronized as follows:

(1) Open the lock on the driver's side door;

(2) Press the unlock button on the wireless remote control key;

(3) Insert the key and turn on the ignition switch;

(4) Turn off the ignition switch again and pull out the key;

(5) Press the unlock button or the lock button.